Kenmore Appliance Specialists
Kenmore Appliance Repair in Groveland, FL
Kenmore appliances have been in American homes for generations, and they aren’t all built the same way. We start with your exact model number, test the part involved and give you a written quote before any repair begins.
What We Cover
A Kenmore Appliance Problem Starts With the Right Diagnosis
For decades, Kenmore appliances were sold through Sears. Over the years, they were built by different manufacturers depending on the product and the era. Two Kenmore washers that look almost identical can have different parts, designs and repair needs.
That’s why we don’t assume anything based on the logo alone. Your model and serial number tell us what’s inside the appliance, which parts fit it and which repair information applies. After that, testing shows us what actually failed.
These are the problems Groveland homeowners usually notice first.
Cooling Isn't Consistent Anymore
The refrigerator feels cold one day and only cool the next, or the freezer shifts between frozen solid and slightly soft.
Laundry Cycles Stop Before They're Done
The washer pauses with water still in the tub, never gets to spin, or stops partway through a normal load.
Drying Takes Longer Than It Should
Jeans and towels need a second cycle, or the dryer runs its full time and clothes still feel damp.
Cooking Temperatures Keep Changing
Baking times aren’t consistent anymore, the oven takes longer to preheat, or one burner heats differently than the rest.
Water, Noise or Error Messages Signal a Problem
Water on the floor, a new grinding or humming sound, or a code on the display that keeps coming back.
Know What a Kenmore Repair Costs Before We Start
Our diagnostic visit is $79, and we waive it when you approve the repair. You get the price in writing first, so nothing on the invoice is a surprise.
Pick Your Appliance
Kenmore Appliances We Repair
Kenmore Refrigerator Repair
Top-freezer, bottom-freezer, side-by-side and French door refrigerators across many model generations.
Kenmore Washer Repair
Top-load and front-load washers that won’t fill, drain, agitate or spin.
Kenmore Dryer Repair
Electric and gas dryers that run cool, stop early or take two cycles to dry.
Kenmore Dishwasher Repair
Built-in dishwashers with drainage, cleaning, latch or leak problems.
Kenmore Oven Repair
Wall ovens and range ovens that won’t heat or don’t hold temperature.
Kenmore Stove & Range Repair
Coil, smooth-top and gas ranges with burners that won’t heat or light.
Kenmore Freezer Repair
Chest and upright freezers, including older models still running in garages.
Kenmore Microwave Repair
Over-the-range and countertop microwaves that stop heating or responding.
Early Warnings
Your Kenmore Appliance Doesn't Have to Stop Completely to Need Attention
Many Kenmore appliances keep running for a while after something starts to fail. Paying attention to small changes can help you avoid a bigger repair later.
Call (352) 562-0907It takes longer to do the same job
Longer dry times, slower cooling after grocery shopping or longer oven preheats can mean a part is losing performance.
It needs a second try
Running a cycle twice or restarting the appliance to get it working is usually a sign of a developing problem.
A little water keeps showing up
Small leaks can damage flooring, subfloors and nearby cabinets before they’re obvious.
The sound has changed
A new squeal, knock or hum usually starts before a part fails completely.
Temperatures drift
Food spoiling sooner or baking results changing are worth checking.
Lights or codes keep returning
If a code or warning light comes back after a reset, the appliance is still detecting a problem.
Symptoms We See
Kenmore Refrigerator Problems That Can Put Food at Risk
Kenmore refrigerators have used different cooling layouts, controls and defrost designs over the years. The same warm-refrigerator symptom can have different causes, so identifying your model comes before testing.
If temperatures keep rising, move the most perishable food to a cooler and keep the doors closed. Our refrigerator repair page explains what we test during a visit.
Schedule Kenmore Refrigerator RepairFresh food section too warm
We check condenser airflow, fan operation and whether frost is blocking the cold air path.
Freezer soft or frosting over
Door seals, the defrost system and the evaporator fan are common areas to inspect.
Food freezing on the shelves
An air damper, temperature control or sensor may be letting too much cold air into the fresh food section.
Water inside or underneath
A blocked defrost drain, a cracked drain pan or a loose water supply line.
Ice maker stopped
We check water supply, the inlet valve, the fill line and the ice maker itself.
Running nonstop
Dirty coils, worn gaskets or airflow problems can make the refrigerator work harder than it should.
Symptoms We See
When Your Kenmore Washer Leaves Laundry Half Finished
Kenmore has sold both top-load and front-load washers, including models with different drive systems, controls and lid or door locks. When a cycle stops, the step where it stopped helps us find the cause.
Slow fill or no fill
Supply taps, inlet screens, the inlet valve and water level sensing are the main areas we check.
Water won’t drain
Clothing, coins or lint can block the drain path. After that, we check the hose and pump.
No spin or weak spin
Most washers won’t spin until they drain and lock. We check drainage, the lid or door lock, and then the drive system.
Agitator or drum not moving
The motor may run while the agitator or drum stays still. We test the drive system on your specific model.
Lid or door lock problems
If the washer can’t confirm the lid or door is locked, it won’t run.
Leaks or excess movement
Hoses, seals, the pump or worn suspension parts may be involved. We level the machine first.
Don’t reach into the tub or force the lid or door open while there’s water inside.
Symptoms We See
Kenmore Dryer Problems That Add Time to Every Load
A dryer needs heat, airflow and moisture sensing to work together. When drying takes longer, we check all three, starting with the easiest to fix.
Have the full vent cleaned once a year. If the dryer smells like it’s burning or feels unusually hot, stop using it until it’s checked.
Warm but slow
A long, crushed or lint-packed vent traps moisture. Cleaning the vent often fixes it without any new parts.
Little or no heat
On electric dryers, we test the heating circuit and safety fuses. On gas dryers, we check the ignition system and gas valve.
Stops before clothes are dry
A dirty moisture sensor, a tripped safety limit or a timer or control problem.
Drum won’t turn
A broken belt, worn idler pulley or motor problem. We confirm the cause before quoting a repair.
Squeaks, thumps or scraping
Worn drum rollers, glides or bearings. Some dryers use slightly different designs, so we check your model.
Symptoms We See
Kenmore Dishwasher Issues That Don't Stay in the Sink
A dishwasher problem can leave dirty dishes, but it can also let water leak into cabinets or onto the floor. Catching it early can prevent more damage.
Water on the floor
A worn door gasket, loose connections underneath or a dishwasher that isn’t level.
Standing water after the cycle
We check the filter, drain hose, air gap or disposal connection, and drain pump.
Dishes still dirty
Blocked spray arms, a clogged filter or water that isn’t hot enough can reduce cleaning.
Door won’t latch
A worn latch or bent strike can stop the dishwasher from starting.
Stops partway through
We check the water supply, heating circuit, latch and controls.
If water reaches the floor, turn the dishwasher off at the breaker and don’t start another cycle.
Symptoms We See
Kenmore Oven & Range Problems That Make Cooking Unpredictable
Kenmore ranges include coil, smooth-top and gas models. Some older units use knob controls, while newer ones use touch panels. Each type has different parts to check.
Oven won’t heat
We check the bake element or gas igniter, the temperature sensor and the controls.
Temperature doesn’t match the setting
We compare the actual temperature with our own meter before making any adjustments.
Coil or smooth-top burner not heating
We check the element, its connection and the switch that controls it.
Gas burner won’t light
A dirty igniter or misplaced burner cap is common. If you smell gas, leave the house and call your gas provider from outside.
Controls or clock not responding
A worn keypad, loose connection or failed control. We test each one.
Worth Knowing
Why the Kenmore Model Number Matters More Than You Might Think
The Kenmore name has been used on many products over the years. Two appliances with the same badge may have different parts, layouts and control systems.
Your model and serial number help us understand how your appliance is built before we start testing. They also help us find the right parts and repair information.
Please send the model number when you book. A clear photo of the label is ideal, especially if the numbers are faded or worn.
- Shows how your appliance is configured
- Helps narrow down compatible parts
- Points us to the right model-specific information
- Helps prevent guesswork during diagnosis
- Lets us check whether parts are available before the visit
Refrigerators and freezers
Check the inside walls of the fresh food section, near the crisper drawers, or inside the freezer lid on chest freezers.
Washers and dryers
Check under the lid, around the door opening, on the back panel or near the control panel.
Kitchen appliances
Look along the dishwasher door edge, behind the range drawer or around the oven door frame.
What Usually Fails
What Could Be Behind Your Kenmore Appliance Problem?
Since Kenmore models vary so much, we test before recommending anything. These are the components we may check depending on your appliance.
Pumps
Drain and circulation pumps in washers and dishwashers. Blockages and worn motors can cause similar problems.
Motors
Drive motors turn the drum or agitator. Fan motors move air in refrigerators, freezers and ovens.
Heating elements and igniters
Used in ovens, electric and gas dryers, and dishwashers that heat during the cycle.
Sensors and thermostats
They tell the appliance when to heat, cool, fill or stop.
Water inlet valves
Used in washers, dishwashers and ice makers. Hard water in Lake County can build up on the screens.
Fans
Evaporator and condenser fans keep refrigerators cool. Oven fans help with even cooking.
Switches and latches
Lid switches, door latches and start switches tell the appliance it’s safe to run.
Electronic controls
Controls are tested last, after we confirm the parts they operate are working correctly.
Reading The Display
Error Codes Help, But They Don't Tell the Entire Story
Many newer Kenmore appliances show codes or flashing lights. Older models may show nothing at all. A code can help narrow down the problem, but it doesn’t tell us what failed.
Codes vary by model family
- Kenmore appliances have been built on different platforms, so the same code can mean different things on different models. We check it against your exact model number.
A code points to a system
- A code may point to draining, heating or door locking. We still test the parts to find the cause.
One reset is reasonable
- After a power outage, a single reset may clear the code. If it comes back, schedule a visit.
Take a photo first
- Take a photo of the code or count the flashing lights before turning the appliance off.
A Few Minutes Now
Help Us Pinpoint the Problem Before the Repair Visit
You don’t need tools, and you shouldn’t remove any panels. A few notes before the visit can make diagnosis easier.
A photo of the model label
Take a clear photo of the full model and serial number label.
The code or light pattern
Write down the code or count the flashing lights.
When it started
Let us know if it started suddenly, gradually or after a power outage or storm.
What still works
Tell us which features still work, like the lights, fans, display or motor.
Clear access
Clear enough room around the appliance for the technician to work safely.
Start To Finish
From Model Identification to Final Testing
Every Kenmore repair starts with identifying the exact model and ends with a full test run.
- 1
Identify the Model
We confirm your model and serial number before planning the repair.
- 2
Hear the Symptoms
You tell us what’s happening and when it started.
- 3
Check the Basics
We look at water, airflow, power and installation first.
- 4
Test the Parts
We test the related parts until we find the cause.
- 5
Quote in Writing
You approve the price before any work begins.
- 6
Final Testing
We run the appliance to confirm it’s working properly.
Honest Advice
Does Repair Still Make Sense for Your Kenmore Appliance?
The answer depends on your specific appliance. Here’s what we look at with you.
- 01
Can we find the parts?
Your model number helps us check whether parts are still available before you commit to a repair.
- 02
How old is it?
Many older Kenmore appliances are still worth repairing, but the specific part and overall condition matter.
- 03
How does the repair compare to replacement?
Compare the repair quote with the total cost of a similar new appliance, including delivery and installation.
- 04
Has it needed repeated repairs?
A first repair is different from several repairs in a short time.
- 05
What else did we notice?
If we see rust, cracks or worn seals, we’ll let you know before you decide.
Fewer Call-Outs
Simple Habits That Can Help Your Kenmore Appliances Last Longer
These habits take only a few minutes, need no tools and are safe for any homeowner.
Vacuum the refrigerator coils
Unplug the refrigerator first, then vacuum the coils once or twice a year.
Don’t overload the washer
Oversized loads strain the motor, suspension and bearings.
Clean the lint screen every load
Have the full dryer vent cleaned once a year.
Rinse the dishwasher filter
Your owner’s manual shows where the filter is and how often to clean it.
Keep door seals clean
Wipe down refrigerator and dishwasher gaskets so they seal properly.
Keep your model number handy
Save a photo of the model label on your phone for future repairs.
Who We Help
Kenmore Appliance Repair for Groveland Homes & Properties
Kenmore appliances are common in older homes, rentals and garages around Groveland. We work with owners, tenants and property managers.
Family homes
Kitchen and laundry repairs scheduled around your household.
Rental homes
We can meet your tenant and send the owner a written summary.
Condos and apartments
Compact and stacked appliances in tight spaces, with access planned ahead.
Property managers
Service calls at multiple properties, grouped by area whenever possible.
Garage and backup appliances
Second refrigerators and chest freezers that need to handle Florida heat.
Where We Work
Kenmore Appliance Repair Near Groveland
Kenmore owners throughout South Lake County call us from Groveland and nearby towns. We help families through appliance service around Minneola, and many garage freezer and laundry repairs come from homes in and around Mascotte. We also serve Clermont and Howey-in-the-Hills.
Answers Before You Book
Kenmore Appliance Repair Questions From Groveland Homeowners
Have another question? Call (352) 562-0907 and tell us what is going on with your appliance.
Why is my Kenmore refrigerator running but not cooling?
Dirty condenser coils, a fan that isn’t running or frost blocking airflow are common causes. Because Kenmore designs vary, we check your model before testing.
What should I check if my Kenmore washer won’t drain?
Look for a kinked drain hose behind the washer. If the hose looks fine, turn the washer off and call us. Don’t take it apart.
Why won’t my Kenmore washer spin?
Most washers won’t spin until they drain and lock. The problem could be drainage, the lid or door lock, or the drive system. We test them in that order.
Why is my Kenmore dryer running without heat?
On electric dryers, it may be the heating circuit or a safety fuse. On gas dryers, it may be the ignition system. A blocked vent can also trip the safety devices.
Why isn’t my Kenmore dishwasher draining?
A clogged filter, blocked drain hose, air gap or disposal connection, or a failed pump are common causes. We check each one before replacing anything.
Why isn’t my Kenmore oven heating?
Electric ovens often point to the element, sensor or controls. Gas ovens often point to the igniter or valve. We test to confirm the cause.
Why do you need my Kenmore model number?
Kenmore appliances have been built by different manufacturers and on different designs over the years. The model number helps us identify the right parts, repair information and diagnosis for your unit.
What does my Kenmore error code mean?
Code meanings vary by model family. Send us the code and model number, and we’ll tell you which system it relates to. We confirm the exact cause during the visit.
Is it worth repairing my older Kenmore appliance?
Often, yes, if parts are available and the appliance is in good condition. We’ll give you a written quote and an honest recommendation.
Do you repair Kenmore appliances outside Groveland?
Yes. We serve Groveland and nearby South Lake County communities, including Clermont, Minneola, Mascotte and Howey-in-the-Hills.
Customer Reviews
What Our Customers Say About Ramson Appliances
4.9 out of 5 stars from 355 Google reviews
- Carmine51
a year ago
Rafael is an Awesome Tech, knows his stuff and explained exactly what needs to be to be done. 100% professional and I will recommend to anyone who needs a trusted a friendly experience…. RAMSON APPLIANCES is without a doubt the best company I have ever had the pleasure to deal with. Thanks so much for a fast response to our call for help! 👍
- Frank Hernandez Jr.
a year ago
Raphael was professional, knowledgeable, polite and courteous. He showed up at the scheduled time, and explained everything he was doing to me. The entire experience was outstanding. I will be using his services again. God bless 🙏
- Desiree Carter
3 years ago
I used Ramsom Appliances to install a dishwasher that I was gifted. My installer, Rafael, was knowledgeable, professional, and overall a pleasure to have for this job. The dishwasher is level, he made sure the water line was installed at the right angle to prevent a backup in the flow of things. The attachment to the garbage disposal was perfect with no leaks afterwards. The front office staff, Ms. Vanessa was also very nice and professional and was able to schedule my service appointment for the next day, which I was very happy about that. I highly recommend RAMSON Appliances. I will use them in the future.
- Christine Stewart
a year ago
Great experience. Scheduling appointment was easy. They gave a heads up via text when they were on the way and they were on time...answered all my questions and gave me a whole education about what was wrong with my refrigerator and how much parts and labor would cost to get to the bottom of it. There were no sleazy tactics to just get my money. Straight up, honest service. I will call again when needed and refer to anyone who needs appliance service.
- Steve Tollerton
a year ago
Easy to contact, quick appointments. The refrigerator lights fix was more difficult than anticipated and took 2 service calls but the tech followed up quickly and i was only billed for the additional parts, not 2 calls. This is the 3rd time we’ve used Ramson and still very satisfied.
Reviews from Google